Atlantik V3 Spectrum Test By Orphek – All Channels combination :
PAR TEST by: Henning Wiese
New LED have been introduced which should increase the spectral balance for coral and the PAR.
The results below are from the first tests with the ASENSE Tech lighting passport.
- Measurement Time: 10/19/2015 19:13:45
- Product Name: Atlantic V3
- Manufacturer: Orphek
- Plant Name:
- User: H. Wiese
- Temperature: 19 ℃
- Distance of Light Source: 0.30 m
- Lamp warm-up period: min
- Height of plant: mm
- Note: New
Atlantik V3 PAR MAP / PAR per Watt / PAR per Meter
PAR per Rang of spectrum
|PPFD (400 ~ 700nm)||729.42 mol / ㎡s|
|PPFD IR (701 ~ 780 nm)||16 511 mol / ㎡s|
|PPFD R (600 ~ 700nm)||79 465 mol / ㎡s|
|PPFD G (500 ~ 599 nm)||111.36 mol / ㎡s|
|PPFD B (400 ~ 499 nm)||538.64 mol / ㎡s|
|PPFD UV (380 ~ 399 nm)||11,001 .mu.mol / ㎡s|
|YPFD (380 ~ 780 nm)||571.96 mol / ㎡s|
|YPFD IR (701 ~ 780 nm)||3.1168 mol / ㎡s|
|YPFD R (600 ~ 700nm)||73 642 mol / ㎡s|
|YPFD G (500 ~ 599 nm)||95 391 mol / ㎡s|
|YPFD B (400 ~ 499 nm)||392.71 mol / ㎡s|
|YPFD UV (380 ~ 399 nm)||6.8250 mol / ㎡s|
|R / B||00:15|
|R / FR||4.81|
|Illuminance||63 022 lux|
|.lambda.p (380 ~ 780nm)||20640 nm|
|λD (380 ~ 780 nm)||443 nm|
Chlorophyll a and chlorophyll b
Spectrum TEST by: Ronny Schöpke
The calculated spectrum is very desirable.
All tests were made with all channels at 100% intensity and the power draw was 185 watts.
But now we will take a look at the Spectrum and the LEDs
The following images show extensive spectral measurements for each channel and with all channels running.
Channel 1 – White & Cyan
Channel 2 – Blue
Channel 3 – Super blue
Channel 4 – Wide Red and White
All channels at 100%
What is striking here is a very important point when comparing to other competitors.
You cannot adjust an Orphek module so that it would cause damage to coral.
Each channel can be set that so it is produces the correct intensity and spectrum for the type of coral one wishes to keep.
Even the full spectrum exists.
Therefore, it is also possible to maintain the V3 with more than sufficient light for SPS coral.
we have also made spectral measurements beneficial to different requirements of coral.
To satisfy the needs of coral, the Orphek Atlantik V3 is a winner.
This is the secret of Orphek LED Lighting.
The V3 does not have clouds and storm effects because they serve no useful purpose for coral care and propagation.
Of course, the usefulness of the available light energy measurement provided superior results. Photonic energy is plentiful with the Atlantik V3.
At a 84 cm distance, we penetrated an extremely high density of water with excellent mol/m2s m (Photons) PAR.
Finally, you get the currently best LED module for the cost.
The Orphek Atlantik not only protects against setting errors and this model has the range to successfully illuminate both aquatic plant and SPS coral. When ordering just specify you’re your application will be and the light will be custom made for you.
This makes the Orphek Atlantik that other manufacturers will try to duplicate.
The measurements of PAR / PUR spectrum are very impressive.
What is not yet on board here is weather simulation but if Orphek does come out with a weather simulation, your unit can be upgraded just by replacing the plug in IC chip.
I hope our readers have found this review to be useful.
Transalation James Gasta
Original post English version : http://www.salzwasserwelten.de/produkttests/beleuchtung/orphek-atlantic-v3-english-vers/